PROMATION Quarter Turn Electric Actuators

• Rugged board design for increased electronic connection reliability
• Patented Self-Locking Drive and Epicyclic Gearing – No Brake or Clutch, increasing mechanical reliability
• Proportional, Jog or On/Off Control – Responds to a wide range of industry-standard signals
• NEMA 4/4X Cast Aluminum Alloy Housing – Resists environmental attack
• ISO5211 Mounting System – No bracket/coupling required for most valves – lower profile
• Standard Internal Heater and Dual SPDT Auxiliary Switches – Normally not standard on other actuators
• Manual override for single-handed positioning (handwheel on P2 and larger, socket on P1 & P1.A series)
• Easy-to-see Raised Position indicator
• Positive Mechanical Stops in base (600 in lbs and above)
• Ambient Operating range -22°F to +125°F (-30°C to +52°C) with internal heater

The PROMATION PZ-6 Series electric actuator is designed for load requirements up to 135 in lbs. This is a compact actuator designed for small space areas. It has a NEMA 4/4X environmental rating, comes standard with an ISO5211 F03/F05 mounting pattern and a 14 mm double-square female drive shaft…making this an ideal actuator for small valve and damper applications. The unit is available as an on/off/jog actuator and in 24 VAC, 120 VAC and 230 VAC supply voltages. Auxiliary switches, heaters, and proportional control cards are not available in this series.

The PROMATION PZ-15 Series electric actuator is designed for load requirements up to 135 in lbs. This is a compact actuator designed for small space areas. It has a NEMA 4/4X environmental rating, comes standard with an ISO5211 F03/F05 mounting pattern and a 14 mm double-square female drive shaft…making this an ideal actuator for small valve and damper applications. The unit is available as an on/off/jog actuator and in 24 VAC, 120 VAC and 230 VAC supply voltages. Auxiliary switches, heaters, and proportional control cards are not available in this series.

The P1 Series electric actuator is designed for load requirements of up to 300 in lbs. The actuator comes standard with two auxiliary switches (shared common, rated at 3A 250V Max), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC/DC, 24 VAC/DC, 120 VAC or 230 VAC supply voltages. The P1 mechanical connections are ISO5211 compliant, utilizing an F03/F05 bolt pattern and an 8 point 14 mm female drive. The P1 Series is available as on/off or two position models that can also be used in bump/jog applications. It can be ordered with an internal proportional control card that accepts a wide range of control signals and generates multiple feedback signals.

The P1.A Series electric actuator is designed for load requirements of up to 445 in lbs. The actuator comes standard with two auxiliary switches (shared common, rated at 3A 250V Max), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC/DC, 24 VAC/DC, 120 VAC or 230 VAC supply voltages. The P1.A mechanical connections are ISO5211 compliant, utilizing an F07 bolt pattern and an 8 point 17 mm female drive. The P1.A Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. It can be ordered with an internal proportional control card that accepts a wide range of control signals and generates multiple feedback signals. This series is available in two different models: The P1.A has built-in manual override capabilities utilizing a 5 mm side-mounted hex key socket, while the P1.A-XOV has no provisions for manual override capabilities.

The P1.B Series electric actuator is designed for load requirements of up to 135 in lbs and a rotation time of 8 seconds. The actuator comes standard with two auxiliary switches (shared common, rated at 3A 250V Max), an internal low power heater, a NEMA 4X environmental rating, and in 12 VDC, 24 VDC, 120 VAC or 230 VAC supply voltages. The P1.B mechanical connections are ISO5211 compliant, utilizing an F03/F05 bolt pattern and an 8 point 14 mm female drive. The P1.B Series is available as on/off or two position models that can also be used in bump/jog applications.

The P1.C Series electric actuator is designed for load requirements of up to 300 in lbs. The actuator comes standard with two auxiliary switches (shared common, rated at 3A 250V Max), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC/DC, 24 VAC/DC, 120 VAC or 230 VAC supply voltages. The P1 mechanical connections are ISO5211 compliant, utilizing an F03/F05 bolt pattern and an 8 point 14 mm female drive. The P1 Series is available as on/off or two position models that can also be used in bump/jog applications. Or it can be ordered with an internal proportional control card that accepts a wide range of control signals and generates multiple feedback signals.

P2 DC: An electric actuator designed for load requirements ranging from 800 to 1335 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VDC or 24 VDC supply voltages. The P2/3 mechanical connections are ISO5211 compliant. The P2/3 DC Series is available as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals.

P2 HV: An electric actuator designed for load requirements ranging from 800 to 1335 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P2/3 mechanical connections are ISO5211 compliant. The P2/3 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications.120V & 230V models can also be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P2 LV: An electric actuator designed for load requirements ranging from 800 to 1335 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC or 24 VAC supply voltages. The P2/3 mechanical connections are ISO5211 compliant. The P2/3 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. 24 VAC models can also be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

*12 VAC models are not available in proportional control.

The P2.0 Series electric actuator is designed for load requirements up to 600 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 24 VDC, 24 VAC, 120 VAC and 230 VAC supply voltages. The P2.0 mechanical connections are ISO5211 compliant. The P2.0 Series can be ordered as an on/off or two position model that can be used in bump/jog applications as well. Models can also be ordered with internal proportional control cards that accept a wide range of control signals (AC versions…DC version is 4-20 mA ONLY), and generate multiple feedback signals for field use.

P3 DC: An electric actuator designed for load requirements ranging from 800 to 1335 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VDC or 24 VDC supply voltages. The P2/3 mechanical connections are ISO5211 compliant. The P2/3 DC Series is available as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals.

P3 HV: An electric actuator designed for load requirements ranging from 800 to 1335 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P2/3 mechanical connections are ISO5211 compliant. The P2/3 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications.120V & 230V models can also be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P3 LV: An electric actuator designed for load requirements ranging from 800 to 1335 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC or 24 VAC supply voltages. The P2/3 mechanical connections are ISO5211 compliant. The P2/3 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. 24 VAC models can also be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

*12 VAC models are not available in proportional control.

The P3.0 Series electric actuator designed for load requirements up to 1150 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 24 VDC, 24 VAC, 120 VAC and 230 VAC supply voltages. The P3.0 mechanical connections are ISO5211 compliant. The P3.0 Series can be ordered as an on/off or two position model that can be used in bump/jog applications as well. Models can also be ordered with internal proportional control cards that accept a wide range of control signals (AC versions…DC version is 4-20 mA ONLY), and generate multiple feedback signals for field use.

P4 DC: An electric actuator designed for load requirements ranging from 3500 to 4400 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VDC or 24 VDC supply voltages. The P4/5 mechanical connections are ISO5211 compliant. The P4/5 DC Series is available as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals. P4 HV: An electric actuator designed for load requirements ranging from 3500 to 4400 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P4/5 mechanical connections utilize an ISO5211 mounting system. The P4/5 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention. P4 LV: An electric actuator designed for load requirements ranging from 3500 to 4400 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC, 24 VAC supply voltages. The P4/5 mechanical connections utilize an ISO5211 mounting system. The P4/5 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention. *12 VAC models are not available in proportional control.

The P4.0 electric actuator is designed for load requirements up to 220 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 24 VDC, 24 VAC, 120 VAC and 230 VAC supply voltages. The P4.0 mechanical connections are ISO5211 compliant. The P4.0 Series can be ordered as an on/off or two position model that can be used in bump/jog applications as well. Models can also be ordered with internal proportional control cards that accept a wide range of control signals (AC versions…DC version is 4-20 mA ONLY), and generate multiple feedback signals for field use.

P5 DC: An electric actuator designed for load requirements ranging from 3500 to 4400 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VDC or 24 VDC supply voltages. The P4/5 mechanical connections are ISO5211 compliant. The P4/5 DC Series is available as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals.

P5 HV: An electric actuator designed for load requirements ranging from 3500 to 4400 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P4/5 mechanical connections utilize an ISO5211 mounting system. The P4/5 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P5 LV: An electric actuator designed for load requirements ranging from 3500 to 4400 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC, 24 VAC, supply voltages. The P4/5 mechanical connections utilize an ISO5211 mounting system. The P4/5 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

*12 VAC models are not available in proportional control.

P6 DC: An electric actuator designed for load requirements ranging up to 5750 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VDC or 24 VDC, supply voltages. The P6 mechanical connections utilize an ISO5211 mounting system. The P6 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals.

P6 HV: An electric actuator designed for load requirements ranging up to 5750 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P6 mechanical connections utilize an ISO5211 mounting system. The P6 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P6 LV: An electric actuator designed for load requirements ranging up to 5750 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 12 VAC, 24 VAC supply voltages. The P6 mechanical connections utilize an ISO5211 mounting system. The P6 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

*12 VAC models are not available in proportional control.

P7 DC: An electric actuator designed for load requirements ranging from 8900 to 13500 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in a 24 VDC supply voltage. The P7/8 mechanical connections are ISO5211 compliant. The P7/8 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals.

P7 HV: An electric actuator designed for load requirements ranging from 8900 to 13500 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P7/8 mechanical connections are ISO5211 compliant. The P7/8 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P7 LV: An electric actuator designed for load requirements ranging from 8900 to 13500 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in a 24 VAC supply voltage. The P7/8 mechanical connections are ISO5211 compliant. The P7/8 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P8 DC: An electric actuator designed for load requirements ranging from 8900 to 13250 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in a 24 VDC supply voltage. The P7/8 mechanical connections are ISO5211 compliant. The P7/8 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Additionally, a proportional control is available to accept 0-5 VDC, 0-10 VDC, 1-5 VDC or 4-20 mA input signals.

P8 HV: An electric actuator designed for load requirements ranging from 8900 to 13250 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P7/8 mechanical connections are ISO5211 compliant. The P7/8 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

P8 LV: An electric actuator designed for load requirements ranging from 8900 to 13250 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in a 24 VAC supply voltage. The P7/8 mechanical connections are ISO5211 compliant. The P7/8 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

The P9 Series electric actuator is designed for load requirements ranging from 17500 to 22000 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P9/10 mechanical connections are ISO5211 compliant. The P9/10 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

The P10 Series electric actuator is designed for load requirements ranging from 17500 to 22000 in lbs. The actuator comes standard with two auxiliary switches  (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P9/10 mechanical connections are ISO5211 compliant. The P9/10 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.

The P11 Series electric actuator is designed for load requirements ranging from 26500 to 31000 in lbs. The actuator comes standard with two auxiliary switches (Form C, 10A @ 250 VAC), an internal low power heater, a NEMA 4X environmental rating, and in 230/3/60, 380/3/60 or 480/3/60 supply voltages. The P11/12 mechanical connections are ISO5211 compliant utilizing an F16 bolt pattern and an Round 75 mm female drive. The P11/12 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention. The -XMCC version does NOT have a motor control center (MCC) attached to the actuator, and is designed to be used with existing MCC’s. The -XMCC versions are designed to operate with 120 VAC control circuits from existing MCC’s.

Note: Because these units are manufactured without an integral MCC, care must be taken during installation to make sure the local phasing is correct for this actuator. This product is shipped at MID-STROKE position to allow up to 20 seconds run time after power-up to determine if the actuator is running in the correct direction. If the MCC is issuing a CLOSE command, the actuator must rotate in a CW direction. If the actuator is NOT rotating in the proper direction, IMMEDIATELY remove power and switch two of the three wires on the motor terminal block inside the actuator. If this verification is not completed within 20 seconds from mid-stroke position, it is possible that the actuator will be damaged due to the motor driving past the respective electrical travel limit switches.

The P12 Series electric actuator is designed for load requirements ranging from 26500 to 31000 in lbs. The actuator comes standard with two auxiliary switches (Form C, 10A @ 250 VAC), an internal low power heater, a NEMA 4X environmental rating, and in 230/3/60, 380/3/60 or 480/3/60 supply voltages. The P11/12 mechanical connections are ISO5211 compliant utilizing an F16 bolt pattern and an Round 75 mm female drive. The P11/12 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention. The -XMCC version does NOT have a motor control center (MCC) attached to the actuator, and is designed to be used with existing MCC’s. The -XMCC versions are designed to operate with 120 VAC control circuits from existing MCC’s.

Note: Because these units are manufactured without an integral MCC, care must be taken during installation to make sure the local phasing is correct for this actuator. This product is shipped at MID-STROKE position to allow up to 20 seconds run time after power-up to determine if the actuator is running in the correct direction. If the MCC is issuing a CLOSE command, the actuator must rotate in a CW direction. If the actuator is NOT rotating in the proper direction, IMMEDIATELY remove power and switch two of the three wires on the motor terminal block inside the actuator. If this verification is not completed within 20 seconds from mid-stroke position, it is possible that the actuator will be damaged due to the motor driving past the respective electrical travel limit switches.http://www.northeastohiowebsitedesign.com/valvepros.com/wp-admin/post.php?post=1664&action=edit#

The P13 Series electric actuator is designed for load requirements up to 40000 in lbs. The actuator comes standard with two auxiliary switches (Form C), an internal low power heater, a NEMA 4X environmental rating, and in 120 VAC or 230 VAC supply voltages. The P13 mechanical connections are ISO5211 compliant. The P13 Series can be ordered as an on/off or two position model that can also be used in bump/jog applications. Or it can be ordered with an advanced internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.